Architectural & Engineering Standards

Plumbing Code Compliance & Technical Specifications

The definitive engineering manual for general contractors, master plumbers, building inspectors, and interior designers specifying handcrafted solid living brass fixtures in North America and worldwide.

Thread Specs
US 1/2" NPT & 3/8"

Standard American tapered pipe threads with zero metric adapters required.

Metallurgy
100% Lead-Free

Virgin binary 65/35 CuZn alloy compliant with US Safe Drinking Water Act standards.

Valve Mechanics
500,000 Cycles

European-engineered diamond-polished ceramic disc cartridges tested to 80 PSI.

Flow Regulation
1.8 GPM & 4.0 GPM

CEC Title 20 kitchen aerators; high-flow full-bore culinary pot filler valves.

01 / Mechanical Interface

North American Plumbing Standards & In-Box Hardware

Every Medina Brass fixture is purpose-machined to integrate directly into standard US and Canadian residential plumbing rough-ins (1/2" NPT and 3/8" compression), and adapts cleanly to UK, European, and Australian 1/2" BSPP metric supply lines using standard solid brass thread reducers:

Fixture CategoryInlet Thread StandardCountertop Bore ClearanceIncluded Supply Hardware
Bridge Kitchen FaucetsUS 1/2" NPT Female / Male Inlets8" on-center (two 1-1/4" to 1-3/8" bores)Heavy brass deck mounting shanks & rubber/brass washers
Single-Hole Monobloc MixersUS 3/8" Compression RisersSingle standard 1-3/8" (35mm) boreBraided 304 SS hot/cold hoses + 1/2" NPT brass adapters
Wall-Mount Pot FillersUS 1/2" NPT Female Wall FittingStandard drop-ear elbow in backsplash wallSolid brass threaded wall nipple & 2.5" cover escutcheon
RO Water Filtration Taps1/4" Quick-Connect & 3/8" AdaptorSingle 1/2" to 1-1/4" holePush-fit John Guest fittings + locknut assembly
Bottle Traps & Sinks1-1/4" OD Tubular Slip-JointStandard US 1-1/2" or 1-1/4" wall drain pipe11.8" extension tube, brass knurled nut, deep wall flange
02 / Metallurgy & Safety

Virgin 65/35 Alloy & Lead-Free Drinking Water Compliance

Unlike mass-market plumbing suppliers that utilize recycled post-consumer brass scrap contaminated with trace lead, bismuth, and antimony, Medina Brass operates an exclusive foundry collective in Marrakech utilizing strictly virgin binary 65/35 architectural copper-zinc ingot.

Zero Zinc Pot Metal or Plastic Cores

Our bodies and spouts are monolithic sand-castings with a density of 8.40 to 8.73 g/cm³. They will never blister, split, or suffer from zinc dezincification stress corrosion.

Oligodynamic Natural Antimicrobial Shield

With 65% pure unsealed copper content, contact surfaces naturally eliminate 99.9% of bacteria and viruses within 2 hours of exposure without chemical disinfectants.

Regulatory Pre-Clearance & External Standards Reference

Our potable water pathways meet the strict requirements of California AB 1953, Vermont Act 193, Maryland House Bill 372, and Section 1417(d) of the US Safe Drinking Water Act (weighted average lead content ≤ 0.25% on wetted surfaces).

03 / Contractor Engineering

Rough-In Heights, Spout Reaches & Valve Clearances

  • Wall-Mount Pot Filler Rough-In: Plumb the cold water 1/2" NPT drop-ear elbow at 12 to 14 inches above the highest cooking grate. For multi-burner professional ranges (Viking, Wolf, Thermador), rough in directly centered behind the range or aligned with the left-rear boiling burner.
  • Bridge Faucet Deck Drilling: Drill two 1-1/4" to 1-3/8" holes at exactly 8.0 inches center-to-center. For Victorian cranked-leg models (MB-KBF-012), articulated leg joints accommodate non-standard drill spreads from 7.8" to 8.4".
  • Single-Hole Gooseneck & Culinary Pull-Downs: Requires a single standard 1-3/8" (35mm) countertop hole. Accommodates solid stone countertops, butcher block, and concrete slabs up to 2.25 inches thick.
  • Independent Side Sprayer Footprint: Drill a single 1-1/4" hole located 4.0 to 6.0 inches to the right of the main faucet spout base for ergonomic single-hand reach.
04 / Long-Term Serviceability

Ceramic Disc Valve Replacement & Worldwide Parts Support

We reject proprietary, obsolete cartridges that leave homeowners stranded ten years later. Every Medina Brass fixture utilizes universal European-standard 1/4-turn and single-lever ceramic disc valves readily available through plumbing distributors across North America, the UK, Europe, and worldwide:

Bridge & Pot Filler Cartridges
1/2" 20-Tooth Spline Ceramic Discs

Standard Kerox / Sedal format. Compatible with universal replacement stems available at local plumbing supply houses worldwide.

Single-Lever Mixers
35mm & 40mm Ceramic Cartridge

Commercial high-temperature ceramic disc mixing cartridge tested for 500,000 cycles at up to 80 PSI municipal pressure.

Free Replacement Guarantee
Express Global Dispatch

Need replacement O-rings, aerators, or cartridges? Email our team at orders@medinabrass.com for immediate 24h dispatch via complimentary express air worldwide.

Explore Specifications by Fixture

Browse Dimensioned Architectural Collections